Take a look at all the great designs and color ways within the Whimsy collection.
Our Sew4Home regular fans, will recognize some similar construction techniques for this pillow from in our recent Black and White Pillow Pile: Double Flange Bolster.
A BIG thanks to our friends at Fat Quarter Shop for providing us with all the Whimsy collection fabrics for our tutorial series. They have a wonderful selection in stock of all the designs. And they are johnny-on-the-spot with all their orders and delivery. Thanks, FQS!
Sewing Tools You Need
- Any Sewing Machine (we recommend the Janome JNH 1860)
Fabric and Other Supplies
- 5/8 yard fabric: we used Joanna Figueroa's Whimsy in Multi Ric Rac Stitching from Moda Fabrics
- 1¼ yard jumbo ric rac: we used bright red
- All purpose thread
- See-through ruler
- Fabric pen or pencil
- Iron and ironing board
- Scissors or rotary cutter and mat
- Straight pins
- Tape measure
- Hand sewing needle
- One medium bag of polyester fiber fill
When working with fabric that has direction, it's very important to watch how you cut the fabric. If this is your first time working with directional fabric, see our tutorial, Checklist: Before You Cut Your Fabric
- Cut two 8” x 8” squares from the fabric for the ends (Joanna Figueroa’s Whimsy in our sample) .
- Cut one 19” x 19½” piece from the fabric for the pillow body (also Joanna Figueroa’s Whimsy in our sample) .
NOTE: We used the same fabric for the main pillow body and the ends, simply changing the direction of the ric rac to add variety. You could vary the project by choosing two coordinating fabrics for your neckroll.
At Your Sewing Machine & Ironing Board
Creating the end 'caps'
- Fold and press one 8" x 8" square in half and then in half again, creating intersecting crease marks.
- Lay the folded, pressed 4" square on your work surface so the center point is in the lower left corner of the square.
- Place a see-through ruler or tape measure at the exact center of this lower left corner and swing the ruler/tape from the top to the bottom of the square, like a pendulum, measuring and marking a dot at the 3¾" point in three to four spots. You are creating a semi-circle.
- Draw an arc to connect the marks. If you own a large compass, you could also use it to create your 3¾" arc.
- Cut on the line to create a 7½" circle.
NOTE: The crease lines will be important in the construction process later; DO NOT repress each circle after cutting.
- Repeat steps 1-5 for the other 8" square.
- Using a long straight stitch, sew ½" around the raw edge of one of the circles. Do not back tack at the beginning or end of your seam. This stitch is for gathering.
- Pull the bobbin thread to gather. Remember those creases you made when the circle was a square? Now, is the time to use these to help you even out the gathers in each quadrant. If this is your first time gathering, see our tutorial, Gathering & Ruffles Made Easy.
- Repeat to create gathers on the other circle piece.
Attaching ric rac and making the body 'tube'
- Pin the ric rac to each 19½" side of the pillow body, ½" from the raw edge, on the right side of the fabric.
NOTE: You should be able to easily tell which sides the ric rac is sewn to by the direction of the print. Also, remember that you want a good portion of the ric rac to stick out from the seam on either end, so consider this when you position it in case your ric ric is smaller than ours.
- Using a zigzag stitch, baste the jumbo ric rac in place.
- Using a ½" seam allowance, sew the 19" x 19½" piece, with its nicely basted ric rac, into a tube. You should pin and stitch along the side without the ric rac - the 19" side. Be sure to start and stop (and back tack) in the middle of the seam to leave a 6"- 8" opening for turning right side out and stuffing.
- In order to create creases that will line up with the creases on each end cap circle, you need to press the tube carefully. First, press the seam open. Then, gently pull the tube with the seam to the right, so you can press a fold directly opposite the seam. Now, gently pull the tube in the opposite direction, matching up the seam and the first crease, and press two additional creases at each side. The seam line and the three creases will match with the quadrant folds on the gathered circles.
- Place one gathered end cap circle inside the pressed tube, matching the seam line with one of the crease lines on the gathered circle. Pin in place. Now, match up and pin the remaining crease lines with each other.
NOTE: If you plan to have the ends match (as in the direction of the pattern), think about that now. Ours are perpendicular to one another so not as much of a brain teaser.
- Adjust gathers as needed within each quadrant. Pin around entire circle.
NOTE: Be sure that you are pinning your circle and tube so the gathered circle will be on the bottom. It's much easier to sew a gathered piece when it's against the feed dogs of your sewing machine.
- You are now going to stitch 'in the round'! This is similar to how set-in sleeves are done.
- Place the pinned neckroll end piece so the raw edge is flipped up a little under the sewing machine foot. This will make it easier to sew around the circle.
- Using a ½" seam allowance, sew around the circle end.
- Repeat for the other end, but before you sew, check to be sure the pattern on the circles is being sewn in the same direction as the previously sewn end.
- Turn the neck roll right side out through the opening.
- Stuff firmly with polyester fiber fill or the filler of your choice.
- Thread a hand sewing needle with matching thread, and hand sew the opening closed.
Hints and Tips
If you're new to sewing, you might also want to check out these helpful articles:
Project Design: Alicia Thommas
Sample Creation: Jodi Kelly
Other machines suitable for this project include the Baby Lock Grace and the Bernina bernette 46.