s4h-janome-8900

Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest

Sew4Home

Eclectic Elements by Tim Holtz for Coats - Fabric Wallet

Printer-friendly versionSend by emailPDF version

Someone told me the other day he believed money would soon become completely digital and we'd be trading electronic credits online. It's happening already to a limited extent with Bitcoins, but it still seems so sci-fi to me. I think I'll hold on to a wallet for now, like today's pretty Eclectic Elements version. I like having physical money with me; a couple paper dollars and some coins just makes me feel happy. I think it goes back to being a kid, when every dime and quarter you hoarded put you that much closer to a giant gum ball from the shiny red dispenser. I still get a little thrill when I find a quarter in my coat pocket, although I worry what a gum ball would do now to my dental work.

Today's wallet features a generous center pocket for bills with four additional smaller slots for credit and ID cards. Plus, there's an exterior zippered pocket for coins and more. An inner layer of extra firm interfacing is pre-stitched prior to assembly, allowing the wallet to easily fold at all the appropriate horizontal points, yet still provide great overall stability for the tri-fold shape.

We really like the Ticking Stripe Tim Holtz added in three colors within the Eclectic Elements collection. It's a great blending fabric, and today we're using the red colorway.  

Eclectic Elements is available now. You can find the entire selection as yardage and bundles at your local independent fabric shop as well as select designs at Jo-Ann Fabric & Craft Stores®. 

The wallet folds to approximately 8" wide by 5" high.

Sewing Tools You Need

Fabric and Other Supplies

NOTE: For the very best look, all your pieces should be carefully fussy cut. The yardage shown allows extra for this purpose. Also, because this piece folds up, you need to pay particular attention to the direction of your prints so everything is right side up when folded closed.

Getting Started

  1. Download and print out the Wallet Corner Cut Pattern
    IMPORTANT: This pattern is ONE 8½" x 11" sheet. You must print the PDF file at 100%. DO NOT SCALE to fit the page.
  2. Cut out the pattern piece along the solid line. 
  3. From the fabric for the main interior, exterior accent and strap (Ticking in Red in our sample), cut the following (stripes should be running vertically on all pieces):
    ONE 9" wide x 15¼" high rectangle for the lining
    TWO 8" wide x 5½" high rectangles for the credit card pockets
    ONE 9" wide x 5" high rectangle for the exterior accent
    NOTE: On the above pieces, make sure the striped pattern is centered to match from one piece to another.
    ONE 9" wide x 7" high rectangle for the zippered pocket
    ONE 16" x 4" strip for the strap
    ONE 4" x 4" strip for the D-ring loop
  4. From the fabric for the main exterior (Butterflight in Red in our sample), cut the following:
    ONE 9" wide x 8¼" high rectangle for the upper exterior
    ONE 9" wide x 4" high rectangle for the lower exterior
  5. From the extra firm interfacing, cut ONE 8" x 14¼" rectangle.  

At Your Sewing Machine & Ironing Board

Prepare the firm interfacing

  1. Find the 8" x 14¼" rectangle of the extra firm interfacing. Place it horizontally and flat on your work surface. If possible use a gridded cutting mat to make your marking and measuring easier. 
  2. Trim the corners from one 8" side (this will become the top of the wallet). To create the proper angle, measure 1" in from the corner and mark, then measure and 1" down from the corner and mark. Connect these marks with a diagonal line and trim along the drawn line with a rotary cutter. 
    NOTE: If you have a gridded cutting mat, you can align the corners against a one inch square on the grid and cut through the middle of the square on the diagonal. 
  3. Measure and mark three vertical lines on the interfacing. Starting from the opposite 8" side from the side on which you cut the corners (this will become the bottom of the wallet), measure and mark one line 5" in from the edge, a second line 10" in from the edge, and a third line 10¼" in from the edge.
  4. Shorten your stitch length; we used 1.80 mm. Stitch along each of the three drawn lines. This stitching helps "break" the firm fusible, which will the wallet to more easily fold into its finished shape. 

Wallet interior and pockets

  1. Find the 9" x 15¼" lining panel and the two 8" x 5½" pocket panels.
  2. Place the lining panel on your work surface, right side up and flat.
  3. Align the Wallet Corner Cut Pattern along the top of the panel and trim the corners to the pattern.
  4. From the bottom edge of the panel, measure and mark two horizontal lines. The first line should be 6" up from the bottom edge and the second line should be 6¾" up from the bottom edge.
  5. Fold each of the two pocket panels in half, right sides together, so they are now 8" x 2¾". Pin along both 2¾" ends.
  6. If necessary, re-set your seam to a standard stitch length.
  7. Using a ¼" seam allowance, stitch both ends on both pieces. Clip the corners.
  8. Turn the pockets right side out and gently push out the corners with a long, blunt end tool, such as a knitting needle or chopstick. Press flat. 
  9. Place the raw edges of one pocket on the 6¾" line and center the ends of the pocket side to side. Pin along the raw edges only.
  10. Using a ¼" seam allowance stitch across the raw edge only. Use a generous back tack to lock the seam at the beginning and end. 
  11. Fold the pocket up, using the ¼" seam as the folding point. The stripes of the pocket should align perfectly with the stripes on the panel. Pin the sides of the pocket to the panel.
  12. In the same manner, place the second pocket along the 6" drawn line. 
  13. Fold the second pocket into position, overlapping the first. Pin the edges of the second pocket through all the layers.
  14. Using a ¼" seam allowance, stitch along the sides of the pocket pair through all the layers. Again, use a generous back back at the beginning and end of the seam for extra security at these pocket stress points. 
  15. Measure to find the exact vertical center of the pocket pair. Draw a line through this center point. 
  16. Stitch along the drawn line to create four, perfectly sized credit card pockets.

Exterior panel and zippered pocket

  1. Find the 9" x 8¼" large exterior rectangle (Butterflight in our sample). If using a directional fabric as we did, orient so the motif is upside down. The fabric should be right side up, vertical and flat on your work surface. 
  2. Align the Wallet Corner Cut Pattern along the top of the panel (the top as you are looking at it with the upside down butterflies) and trim the corners to the pattern. 
  3. Find the 9" x 5" accent panel (Ticking in our sample) and the 9" x 4" small exterior rectangle (Butterflight in our sample).
  4. Place the accent panel right sides together with the bottom edge of the large exterior rectangle. Pin in place. Stitch together, using a ½" seam allowance.
  5. Place the small exterior rectangle right sides together with the remaining raw edge of the accent panel. Make sure your directional motif is still upside down. Pin in place. Stitch together, using a ½" seam allowance. Press the two seams open and flat.
  6. Find the 9" x 7" zippered pocket panel and the 7" zipper.
  7. Place the fabric panel wrong side up on your work surface.
  8. With a fabric pen or pencil, draw a 7" x ½" narrow box. This narrow box should be centered side to side on the pocket panel and ½" down from the upper edge.
  9. Find the sewn 3-part exterior panel. Place it right side up and flat on your work surface. Within the large exterior panel (the panel with the clipped corners), measure 2" up from its seam line with the accent panel and place a pin at each outside raw edge.
  10. Place the pocket panel with the drawn box right sides together with the exterior panel, aligning the top edge of the pocket (the edge ½" from the drawn box) with the the two pin marks. Pin the layers together through the box.
  11. Stitch along the drawn box, using a shortened stitch length (we used 1.80 mm again).
  12. Cut through the center of the box, then clip into each corner. You are cutting through both layers.
  13. Turn the pocket right sides out through the opening, smoothing the corners of the box. Press flat.
  14. Flip the panel to the right side. Place the opening over the zipper, centering the coil. Pin in place. 
  15. Re-set the stitch length to standard.
  16. Edgestitch the zipper in place.
  17. Go around all four sides, opening and closing the zipper as necessary to keep the tab out of the way of the needle.
  18. Flip back to the wrong side again. Fold just the pocket layer in half, bringing the lower edge of the pocket up so it aligns with the upper edge. Pin in place.
  19. Flip over yet again to the right side. From the right side, edgestitch through all the layers from one end of the zipper to the other, running your seam directly over the top of the zipper edgestitching farthest from the seam. In other words, you are just stitching just one seam here and it is directly on top of one side of the zipper's edgestitching. 
  20. Place the exterior and lining panels right side up and flat on your work surface with the flat ends (the corner cut ends) at the top.
  21. Mark each piece for the placement of the magnetic snap. 
  22. The first half is placed on the exterior panel ½" above the accent panel/lower panel seam and centered side to side. 
  23. The second half is placed on the lining panel 1" down from the top raw edge of the flap and centered side to side. (The photos and drawings below have the best image of this snap position if you are unsure.)
  24. Following manufacturer's instructions, insert each half of the snap. 
  25. We also added our Sew4Home label within the accent panel. 

Assemble front to back

  1. Place the lining panel right side up and flat on your work surface. 
  2. Place the exterior panel right side down on top of the lining, matching all edges.
  3. Center the extra firm interfacing on top of the wrong side of the exterior panel and pin in place through all the layers. Leave a 4" opening along the bottom straight edge.
  4. Sew around the entire perimeter with a ½" seam allowance, which should just catch the interfacing. Remember to lock your seam at either side of the 4" opening at the bottom of the wallet. Clip the corners.
  5. Turn right side out through the bottom opening. Gently push out all the corners with a long, blunt-end tool so they are nice and sharp. Press well, pressing in the raw edges of the 4" opening so they are flush with the sewn seam. Pin the opening.
  6. Edgestitch across the bottom only, starting and stopping at the sides. This closes the opening used for turning. 

Strap and loop

  1. Find the 4" x 16" strap strip, the 4" x 4" loop strip and the D-ring. 
  2. Fold the strap strip in half lengthwise and press to form a center crease. 
  3. Open the strip wrong side up so the crease line is visible. Fold in each raw edge so they meet one another at the center crease line. Press well. 
  4. Fold the strip in half along the original crease line, aligning the folded-in edges. 
  5. Edgestitch along both long sides. The ends remain raw.
  6. Repeat to create the loop strip.
  7. Place the wallet lining side up and flat on your work surface.
  8. Slip the loop through the D-ring. Align the raw ends. Place the D-ring and loop just above the credit card pockets. Pin in place so the D-ring extends just beyond the edge of the wallet.
  9. Fold up the lower section of the wallet. It should easily fold 5" from the end thanks to those stitching lines previously sewn into the interfacing. Pin the folded section in place, sandwiching the loop ends between the layers.
  10. Edgestitch through all layers starting at the bottom fold, going up one side, around the entire flap, then back down the opposite side (again through all those layers... go slowly!), ending at the opposite bottom bold. You may need to lift up the presser foot slightly to stitch around the magnetic snap at the top.
  11. The D-ring and loop are now secured within this edgestitching. Reach inside and remove the pins that were holding the loop. Trim the ends of the loop back to ¼" so they are not in the way of the credit card pockets.
  12. Insert the strap through the D-ring. Overlap the raw ends, folding them under on one another to enclose the ring and the raw edges. Pin in place.
  13. Stitch a ¾" "X-box" through all the layers to secure the strap.  
  14. Fold the flap and fasten with the magnetic snap. The flap should fold easily, again thanks to that inner line of stitching on the interfacing.  
     

Contributors

Project Design: Alicia Thommas
Sample Creation and Instructional Outline: Michele Mishler

Tags: 

Section: 

Comments (11)

Susan Mac Donald said:
Susan Mac Donald's picture

Thank you for the inspiration!! The pattern is so well presented; now, only to find a distributor for T.H & I'll be ok to submit my order.

Noreen said:
Noreen's picture

I love this wallet! Especially the color - red being my favorite. It would be so handy to pull out of your bag to carry by itself if you just want something small.

Noreen

missusg said:
missusg's picture

i made a wallet long time ago with canvas and paint and loved it.. i LOVE this!!!!! 

Donna Gibson said:
Donna Gibson's picture

Oooh, I love how this opens for the zipper section!  Great design!

kittyklaws65 said:
kittyklaws65's picture

In the second picture you have an inset picture of the inside of wallet looking down into the credit card slots. Is that covered? Creating a pocket for cash? Is that what we're seeing? 

Again S4H did an amazing job creating a project I've been wanting to do. The wallet I wanted in store was so ridiculously priced and not as nice as yours. Could this be created with leather? Love the material you chose! Love ticking!!!!!!!!!!  

Thanks ladies for another wonderful project 

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@ kittyklaws65 - if you read through the instructions, I think you'll see how it all folds up. The credit card pockets are stitched at the center and the bottom folds up with the sides stitched into place. We made this wallet specifically for the Eclectic Elements fabric. Not sure how it would translate into leather.

ska said:
ska's picture

Love this project. Can't wait to get started! Thanks for the very clear tutorial. 

EvaMaria said:
EvaMaria's picture

I've been looking for a wallet with just the right number of credit card slots and I never thought to just make one myself! Thanks for the inspiration! This is a great wallet!

paula cheney said:
paula cheney's picture

Amazing tutorial.  I have sewn for many, many years and I learned so much today.  That "zipper in a box" was fab.  Your tutorials and photos are top notch.  Just amazing skills all around.

paula

Yan said:
Yan's picture

Reading through the instructions, it sounds to me like the wallet would finish up as about 8 inches wide by about 5 inches high. Is it folded in half somewhere where I'm not reading so that it ends up as only 4inches wide? Thank you. I'd really like to sew a wallet that's about 4"x5", with all these components, especially the zippered coin purse, easier to carry in my hand if I don't want to carry a handbag.

tora said:
tora's picture

This is really cool, I just wish Tim´s fabrics were here close to where I live (it´s so expecive to have them shipt over) :(

Add new comment

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business.
By submitting this form, you accept the Mollom privacy policy.