New Janome General-Leaderboard Left
Janome General-Leaderboard right

Facebook Twitter Sew4Home RSS Feed Follow Me on Pinterest Instagram


Insulated Baby Bottle Carrier

Printer-friendly versionSend by emailPDF version

Babies and their entourages (sometimes referred to as parents) are always on the go: to the store, the park, the playgroup, the zoo, anywhere and everywhere. When they're out and about, they like to have their favorite drink nearby. Mom gets her 'Bucks venti half white mocha, half cafe vanilla, ez ice, 2 shots pour appigato style with whip and caramel drizzle frappachino (actual order overheard at one of our local Starbucks®)... baby gets his/her bottle - nicely warmed or chilled, thank you very much. It's an easy request to fill thanks to our baby-on-the-go thermal baby bottle carrier. There's a water resistant PUL lining, a layer of insulating batting, and a super trendy fabric exterior with a handy Velcro® strap.Our Bottle Carrier sample got rave reviews from everyone here in the studio. Those who don't need a baby bottle version were already scheming on up-sized versions as a thermos carrier or a wine bottle carrier/gift bag. We did our own Re-imagine & Renovate version as a water bottle pod for the gym: the Weekend Wonders Water Bottle Sling

We originally used two fabrics from the Oh Deer! collection by MoMo for Moda Fabrics. This in an older collection that can be hard to find now. As an alternative, we found two cute options: 1) Birch Farm Egg Blue Barn Owl with Egg Blue Chicken Coop by Joel Dewberry for Free Spirit Fabrics.

2) Marine Too Organic Angel Fish and Organic Waves and Whales by Dan Stiles for Birch Fabrics.

The carrier is sized for a standard baby bottle and finishes at approximately 9" tall with a 3" diameter base, for which a pattern is offered below.

Sewing Tools You Need

Fabric and Other Supplies

All our pieces were fussy cut for a vertical reveal. If your motif is very distinct, you may want to up your yardage by ⅛ to ¼ yard in order to give yourself a little extra with which to work. 

  • ¼ yard of 44-45" cotton fabric for the carrier top and facing; we used Dot in Bright Sky/Bark from the Oh Deer! collection by MoMo 
  • ¼ yard of 44-45" cotton fabric for the carrier bottom, base and strap; we used Sparrow in Bark from the Oh Deer! collection by MoMo
  • ⅓ yard of 60" wide of Polyurethane Laminate (PUL) for the carrier lining; we used 1 ml PUL in White from
  • ½ yard of medium weight fusible interfacing, we used Heat 'n' Bond fusible from 
  • ⅓ yard of thermal batting; we used Insul-Bright Mylar/Poly batting from
  • Scrap of ½" wide sew-in Velcro®; you only need about 2", we used black
  • All-purpose sewing thread in colors to match fabric
  • Scissors or rotary cutter and mat
  • See-through ruler
  • Straight pins 
  • Clips for PUL
  • Seam gauge 
  • Seam ripper
  • Iron and ironing board

Getting Started

  1. Download and print the Bottle Carrier Base pattern.
    IMPORTANT: This pattern download consists of ONE 8½" x 11" sheet. You must print this PDF file at 100%. DO NOT SCALE to fit the page.
  2. Cut out the pattern along the solid line.
  3. From the fabric for the carrier top and facing (Dot in Bright Sky/Bark in our sample), fussy cut ONE 5" high x 10½" wide rectangle.
  4. From the fabric for the carrier top, base and strap (Sparrow in Bark in our sample), fussy cut the following:
    ONE 7½" high x 10½" wide rectangle
    ONE 3" x 13" strip
    Using the pattern, cut ONE base circle
  5. From the PUL cut the following:
    ONE 9½" high x 10½" wide rectangle
    Using the pattern, cut ONE base circle
  6. From the fusible interfacing, cut the following:
    ONE 9½" high x 10½" wide rectangle
    ONE 3" x 13" strip
    Using the pattern, cut ONE base circle
  7. From the insulated batting cut ONE 9" high x 9½" wide rectangle. Trim away the seam allowance from the base pattern (trim along the dotted line). Using this smaller pattern, cut one base circle from the insulated batting.

At Your Sewing Machine & Ironing Board

Main exterior panel

  1. Find the bottom exterior rectangle (the Dot in our sample) and the top exterior rectangle (the Sparrow in our sample). Align the top raw edge of the bottom section and the bottom raw edge of the top section (whoa... ya gotta think about that one!). Pin in place.

    NOTE: If you are using a directional motif, like our pretty sparrows, double check to make sure they will be facing (or in our case, flying) in the right direction once the seam is sewn.
  2. Using a ½" seam allowance, stitch the two pieces together. Press the seam allowance toward the top.
  3. Flip this exterior panel over and edgestitch along the seam within the top fabric. 
  4. Find the 9½" x 10½ rectangle of interfacing. Place the interfacing on the wrong side of the exterior panel you just finished, matching the bottom edges and the sides. There should be 1½" of fabric extending beyond the interfacing along the upper edge. 
  5. Following manufacturer's instructions, fuse the interfacing in place. 
  6. Fold down ½" along the top raw edge and press. Fold down an additional 1"  and press again to create a finished 1" hem. Press in place only; the stitching will be done in a later step.

Carrying strap

  1. Find the 3" x 13" strip. Following manufacturer's instructions, fuse the 3" x 13" interfacing piece in place on the wrong side of the fabric strip.
  2. Press under ½" on both ends. 
  3. Fold the entire piece in half lengthwise to set a center crease. Unfold so this crease line is visible.
  4. Fold in each long side to meet the center crease line.  
  5. Fold again along the original center crease line, matching the folded edges. Pin in place. 
  6. Edgestitch around all four sides, pivoting at all the corners.  
  7. Find the 2" strip of Velcro®. Position the hook side at one end of the strap, just ⅛" from the finished end. 
  8. Stitch the Velcro® to the strap with an "X box" - around all four sides and an X through the middle. We have a nice, step-by-step tutorial on this technique

    NOTE: This Velcro® needs to be able to take a lot of opening and closing, which is why we recommend the X stitch through the center.
  9. Place the exterior panel right side up on your work surface.
  10. Measure to find the center of the top edge. Mark the center with a pin. Measure 2⅜" to the right of center and mark with a pin. Measure 2⅜" to the left of center and mark with a pin.
  11. Unfold the hem so the panel lays flat
  12. Find the loop side of the Velcro® strip. Center it on the leftmost mark. The bottom of the Velcro® should be ½" above the top/bottom horizontal seam. 
  13. Find the strap. Center the plain end (the end with no Velcro®) on the rightmost mark. The finished end of the strap should be ½" above the top/bottom horizontal seam. The strap should have its right side facing up, which means the opposite end with the Velcro® is facing down.
  14. Stitch the strap in place with an "X box."
  15. Stitch the Velcro in place with an "X box."

Create the tube and insert the base

  1. Find the exterior base circle. Following manufacturer's instructions, fuse the interfacing circle in place on the wrong side of the fabric circle. Set aside.
  2. Stay stitch along the bottom of the exterior panel ½" from the edge. Clip approximately every ½", taking care to not cut through the stay stitching.

    NOTE: Stay stitching is a single line of stitching that simply helps stabilize the fabric to prevent stretching or distortion. In this project, it will also provide us with a seam line to follow later in the instructions.
  3. Fold the exterior panel in half, right sides together, to create the center back seam. Be careful to match the top horizontal seam line. Pin in place. Remember, the top hem is still unfolded.
  4. Using a ½" seam allowance, stitch in place.
  5. On the fused base circle, place a pin at the exact center top, exact center bottom and the center points of each side. Think of it like a clock face with pin points at 12:00, 3:00, 6:00 and 9:00. You can also fold the circle in half and then in half again, and place a pin at each fold.
  6. On the carrier tube, the corresponding 12:00 point will be the center of the center back seam. Keeping the seam in the exact center, flatten the tube to find the opposite 6:00 point. Then, flatten the tube in the opposite direction to find the 3:00 and 9:00 points. Place marking pins at all these points. 
  7. Place the base right sides together with bottom circular opening of the tube, aligning all the pin points. Easing the fabric, fill in the rest of the circle with pins. If you have done garment sewing, this is very similar to putting in a sleeve.
    NOTE: If you are new to this technique, we have a full, step-by-step tutorial on inserting a flat circle into a tube
  8. Stitch the layers together, following the original line of stay stitching. 
  9. Trim back the seam allowance to ¼".

PUL lining and thermal wrap

  1. Find the PUL rectangle and circle.
  2. Run a line of stay stitching along one 10½" edge of the rectangle. As above, clip approximately every ½", taking care to not cut through the stay stitching.
  3. Fold the rectangle right sides together, aligning the 9½" sides.
  4. Using a ½" seam allowance, stitch in place.
  5. Following the same steps as above, insert the PUL base into the PUL tube and stitch in place, following the line of stay stitching. 
  6. Find the thermal batting rectangle and circle.
  7. Set up your sewing machine for a large zig zag stitch. We set our stitch at 5.0 mm wide and 1.5 mm long. 
  8. Fold the rectangle right sides together, aligning the 9" sides. Pin in place.
  9. Sew the edges together with a zigzag stitch. The needle should penetrate the fabric on the left swing, then go off the edge of the fabric on the right swing of the needle. Remember to lock your stitching at both the beginning and end.
  10. Gently tug the seam to flatten it. The edges of the fabric should butt together.
  11. Following the same steps as above, mark the thermal tube and base.
  12. Then insert the base into the tube and stitch in place, again using a zig zag stitch. 

Assemble all three layers

  1. With the thermal tube right side out and the PUL lining tube wrong side out, slip the lining tube inside the thermal tube. Align the seams and the upper edge. Pin or clip in place.
  2. With the exterior tube right side out, slip the two layer lining tube inside the exterior tube. Match the upper of edge of the PUL/thermal tube to the bottom crease line of the exterior tube's unfolded hem. 
  3. Fold the hem back into place along the original crease lines, first folding ½", then folding an additional 1". It should just cover the top raw edges of the interior tubes. Pin in place.
  4. Edgestitch the hem in place close to the inner fold all the way around through all the layers. Remember to pull the strap up and out of the way.


Project Design: Alicia Thommas 
Sample Creation and Instructional Outline: Michele Mishle



Comments (9)

jasonbrown said:
jasonbrown's picture

It is really amazing; we are always looking for best baby products online and from baby stores. But here we have found a beautiful handmade insulated baby bottle carrier, even I believe that it would be very tough to follow the guidelines from here but I will definitely try my best to give such a beautiful output. It was really appreciable and adorable.

judithwiegand said:
judithwiegand's picture

I am trying to make a hugabub baby carrier but I am not that much good at sewing. I found your post to be very inspirational and I got some easy tricks to complete my carrier.

Mrs T said:
Mrs T's picture

Can we make a closing on the top of some kind? Maybe a top flap or a pouch kind of closing?

Judi said:
Judi's picture

 I'm actually going to adapt this pattern to carry a portable water container (Water Rover) for my dog when we hike to keep the water cold. I plan on making a drawstring top that will make it a little more contained and easy to open and close. I've seen similar to carry people water bottles - they have the silver thermal lining so I may use that material. Is there such a creature as a nylon material that actually has the silver backing attached or would you need to do it in two layers - one nylong and one Quik-Silver?

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@ Mrs T - you could certainly make it taller and incorporate a flap or even a little zipper. Let us know if you go ahead with this plan. In the meantime, we'll add your upscale suggestion to our You Asked 4 It list. 

TimelessKreations said:
TimelessKreations's picture

These really work, my friend wanted me to tell you thank you very much. Made her two and then she asked for 2 more. She is nursing, so she pumps at night before going to bed and it is keeping the bottle warm for the night feedings, she feels it is safer and healthier. Thank you as well.

Liz Johnson.Editor.Sew4Home said:
Liz Johnson.Editor.Sew4Home's picture

@ TimelessKreations - great to hear. So glad your friend is lovin' them. 

sissitouchatout said:
sissitouchatout's picture

It is exactly what I want to do, to offer wine or champagne to my friends. I  shall make mine larger than this one for baby.

Thanks !

Add new comment

*Sew4Home reserves the right to restrict comments that don’t relate to the article, contain profanity, personal attacks or promote personal or other business.
By submitting this form, you accept the Mollom privacy policy.